Guide :Camping, Backpacking & Hiking : Flashlight Type: Black D Cell 5: 5

Have put new batteries in bulb is ok just stopped workin 5 cell dd batts

Posted by Shaun Trevena on Aug 04, 2009

Research, Knowledge and Information :

5 Main Reasons Why Your Solar Lights Are Not Performing as ...

... (5 main reasons why your solar lights are not ... and now both sets have stopped working completely,they are ... not working with new batteries, ...
Read More At :

Tips and Trick for Solar Outdoor Lighting Troubleshooting

These tips and tricks for solar outdoor lighting troubleshooting helps you figure out what ... just like a light bulb in ... new batteries installed in all of ...
Read More At :

Battery Tips! - For Household Batteries (AAA, AA, C, D, 9V)

Different devices stop working at ... Batteries put out juice when ... The general public uses the word "battery" instead of "cell" ...
Read More At :

Batteries in Maglite leaked-now it won't work! | ...

Batteries in Maglite leaked-now it won ... I removed the bulb. I put a board on the floor and dropped the flashlight ... batts were dead, put in some new ones and it ...
Read More At :

How to Repair a Solar Powered LED Garden Light: 4 Steps

This is a guide on how to repair your light if you have had it for a few years and the stress of the outdoors have caused it to stop working. Honestly, why won't ...
Read More At :

General FAQs - Maglite

General FAQs. Click to Expand. You ... if you have a 4-Cell Mag-Lite® flashlight and you put a 2-Cell or 3-Cell lamp inside, ... Putting new batteries together with ...
Read More At :

Repairing solar lights after battery replacement failed ...

Repairing solar lights after battery replacement failed. ... Batteries are new. ... Have you just tried swapping the batteries from the working ones?
Read More At :

A Guide to Understanding LiPo Batteries — Roger's Hobby Center

A Guide to Understanding LiPo Batteries. Home / News / ... If you have large capacity batteries, large cell ... LiPo batteries have all sorts of power just waiting to ...
Read More At :

Suggested Questions And Answer :

Have put new batteries in bulb is ok just stopped workin 5 cell dd batts

First of all are you certain the bulb is ok? Test for continuity across the light bulb. The filament in light bulb will have a very low resistance. if you are not handy with a multimeter then respond back with a new thread and I can give you more tips on using a multimeter. Next, clean the contact surfaces off where the battery terminals contact the flashlight copper contacts. You can use a high grit sand paper if necessary. They sell battery terminal cleaner solutions/supplies at Automotive stores if you like. However, distilled water and/or alcohol will probably work just as good. Next connecting one probe of your multimeter to the top inner contact and then the other probe of your multimeter to the lower inner contact turn off and on the switch. When the switch is on, you should see the same resistance that you checked the resistance of the light bulb filament. If you don't see the same resistance then switch is bad. If resistances are equal then place batteries back in flash light and everything should be good to go!
Read More At : Flashlight Type: Black D Cell 5: 5...

Put new batteries in it,turned it on and still wont work,you think it might be the bulb

Before replace the bulb, check for rust or dirt inside the electrical contacts. clean it. if still wont work, replace the bulb. sammyc47
Read More At : 4 Cell C Flashlight Black...

Got new Energizer Hard Case Flashlight model IN421

Well much to our surprise the easy way is the best way. There are no instruction on the package nor on Energizer website but after googling we found reviews of the flashlight and how long it took others to find out how to put the batteries in. Although the base is DOES turn and voila....comes off to insert batteries.
Read More At : Energizer...

I replaced the batteries and it dose not work. Yes the batteries are new and in the right direction.

You should check the light bulb. Probably broken.
Read More At : Flashlight Type: Black D Cell 5: 5...

I have a GE battery powered (4 D cells) camping lantern. It will not turn on. The batteries are new and have been tested. Is there a way to remove the fluorescent and check?

Fluorescent lamps need a high voltage in order to ionise the gas inside and make them light up..Torch batteries will not produce enough voltage alone so the battery voltage is boosted by an inverter that is incorporated into the torch or lamp body. It is unfortunate but the majority of such lamp inverters use the cheapest, nastiest, flimsiest circuitry it is possible to use in such things and having taken a few lamps and torches (of respectable brands) apart and seen such things I find it easy to imagine they were thrown together in a far eastern handbag factory when there was a world slump in handbag sales. When working correctly the inverter produces a voltage high enough to really surprise anyone touching the wrong parts but they do tend to be unreliable due to the usually low quality. A handy person could conceivably persuade such a lantern to dismantle and check the switch and wiring and ensure the battery voltage is reaching the inverter but it would need electronic experiece to venture further into the reasons why it stopped working. A replacement tube could be tried but they fail rarely and rarely do they operate long enough to actually wear out so buying a new tube is likely to be wasted money.
Read More At : SteelBEAM FluorescentLED Hybrid Lantern Black...

LED Flashlight Battery Drain Problem

This particular flashlight uses a microchip that consumes the power of the batteries, whether in use or not. Loosen the case to where the batteries go in, so there is no contact with polarity. Or just take the batteries out completely and replace them for actual use. GGBMDB
Read More At : Streamlight 75000...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0309 seconds