Guide :Camping, Backpacking & Hiking : Northstar Dual Fuel Lantern

I can't build up pressure in my Model 200A lantern. I oiled the pump and expanded the element but that did not help. With the air valve closed and my thumb on the pump I can fee pressure. With the air valve open, after I pump a while if I take my thumb off the pump air leaks out. Any idea of the problem and solution?

Posted by rsears123 on Aug 30, 2011

Research, Knowledge and Information :

8 Reasons You Should Care a Lot About the 2020 Census

You do it by where you open up ... Pressure your reps to care ... to occur every ten years whether we’re ready or not. And you can’t re-do a ...
Read More At :

Lawsuit: Over 99 Percent of Uber’s NYC Cars Inaccessible to ...

Getting rid of CEO Travis Kalanick has apparently not magically resolved all of ride-hailing giant Uber’s many, many problems, with the company now facing a lawsuit ...
Read More At :

What to Do If You Make a Big Mistake at Work - Lifehacker

... own up to your actions and commit to finding out what happened ... following your mess-up. Take care not to make any more ... while yes, it won’t ...
Read More At :

Check Out How Samsung Describes Its Male and Female Bixby ...

Samsung's Bixby Assistant Delayed Again Because It Can't Learn ... “I think that job displacement is a huge problem, ... That did not work out so well for the ...
Read More At :

Dragon | Ships | Bomb - Scribd

... but $ know we can pull this mission off. $n my humble opinion you ... it into the air pressure lock before ... to decrease the debt burden and pump up the ...
Read More At :

Dragon | Boeing B 29 Superfortress | Ships

... but I know we can pull this mission off. In my ... be air-dropped out the cargo doors. "I wouldn't be ... up for a while. I'll wager we can ...
Read More At :

CALCITE SCREENINGS 1929 by Presque Isle County Historical ...

Title: CALCITE SCREENINGS 1929, ... As George left the main highway and started off up a dirt ... some of our good streams open again after be ing closed for several ...
Read More At :

JuJa Italia

Top VIdeos. Warning: Invalid argument supplied for foreach() in /srv/users/serverpilot/apps/jujaitaly/public/index.php on line 447
Read More At :

Suggested Questions And Answer :

Need a valve cap for two double Embark Twin air mattersses, mine were missing in my boxes.

Contact seller it should be their problem
Read More At : Twin Double High Air Mattress with Built-in-Pump...

I'm looking for instructions or manual for Medline Sentry 1200 pressure regulating mattress

Utube or call a store
Read More At : Sentry 1200 Mattress System - Alternating Pressure/Low Air...

Can you find and seal a slow leak? - Embark Twin Double High Air Mattress with Built-in-Pump

Finding the leak is the fun part as what you need to do is pump up the mattress and wipe an area with very soapy water to make bubbles at the leak site and do that until you find the leak Then depending on where the leak is the repair is easy to very difficult Easy will be any flatish surface to difficult a edge or seam leak Take a look at YouTube for airbed leak home repair and delete code from there what you want to do
Read More At : Twin Double High Air Mattress with Built-in-Pump...

Acts like a check valve is stuck open below the plunger assembly. It lets all the pressure out while im trying to pump it this something i can fix? the lantern is relatively new.

It sounds like you are correct. While I don't know much about the new lanterns I have worked a lot on older ones. My first suggestion is the easiest. Try putting some 3 in 1 oil on it. First relieve any pressure in the tank- open the valve then slowly loosen the fill cap- watch out as it will likely spill fuel so do this outside Remove the plunger, there is a black plastic piece that holds it in it will come of either by a push and twist, or by removing a little metal bail across it. (you remove the metal bail (small wire loop) by gently pulling it outward with a small pliers.) then the plunger should come right out look into the hole and you will see a check valve at the bottom, try a bit of oil or wd40 on this, let it sit for a while, it may just be rusted open, and will take some time for the oil to work. Make sure it is working well before you light the lantern. you Do Not want this to fail when the lantern is going. Do this outside and away from any flames. Pump it up and see if it can hold pressure overnight
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0198 seconds