Guide :Camping, Backpacking & Hiking : Xl100

Flashlight will not stay on unless I keep pressing on the switch.

None of the functions are working, and the light wont stay on after I release the button,same problem as Jordan S Now the light will not keep a steady beam, It flashes when I hold down the power button.

Research, Knowledge and Information :


3 Ways to Fix a Stuck Brake Light - wikiHow


Sep 02, 2016 · Brake lights are intended to keep other ... wiki How to Fix a Stuck Brake Light. ... the switch. If not, disconnect it now by pressing on the plastic ...
Read More At : www.wikihow.com...

Light will not Turn Off using light switch - Forum - Bob Vila


Light will not Turn Off using light switch; BV002735. ... the light continues to stay on, changing the switch did not fix this ... 10 Things Always to Keep Near Your ...
Read More At : www.bobvila.com...

Maglite MAGTAC LED 2 CELL CR123 PLAIN - Maglite


Maglite MAGTAC LED 2 CELL ... it’ll only stay on as long as I keep pressing the switch ... battery power — to make sure your flashlight doesn’t just ...
Read More At : maglite.com...

truck wont stay running - CarGurus - Used Cars, New Cars ...


truck wont stay running - I have a ... my truck was running fine light was left on want stay on unless u keep kyour foot on the ... You have to turn switch off and ...
Read More At : www.cargurus.com...

Give me 5 Minutes and I'll Fix Your Fluorescent Light


Has your fluorescent light ... Now I can’t get the bulb to stay in place and keep the bulb lit unless I stay there on the ... When I flip light switch it comes ...
Read More At : www.homerepairtutor.com...

lighting - Dimmer switches & LED lights: Lights keep turning ...


We have a dimmable light switch panel in our lounge ... Dimmer switches & LED lights: Lights keep turning up to max ... I was hearing a maddening low hum unless on ...
Read More At : diy.stackexchange.com...

How Brake Light Wiring Works - Auto | HowStuffWorks


Learn all about connecting to the brake light switch ... How Brake Light ... Your brake lights may not light up when you press on the brake pedal or they may stay ...
Read More At : auto.howstuffworks.com...

How To Diagnose Brake Light Problems - AGCO ... - Baton Rouge, LA


Pressing the pedal should cause the switch ... Unplug the brake-light switch and if the lights stay on, a ... brake light switch? Jmcreynolds86 - June 7, 2016 I keep ...
Read More At : www.agcoauto.com...

10 Reasons Why Your Lights Don't Work - Networx


10 Reasons Why Your Lights Don't Work ... 7 Outdoor Lighting Tips To Keep You Safe This Summ... ... Cost to Install a Light Switch ;
Read More At : www.networx.com...

FAQs - Streamlight


FAQs; Training ... I have replaced the Xenon bulb but it still does not light. ... Is there a way to keep this from occurring again?
Read More At : www.streamlight.com...

Suggested Questions And Answer :


Hello, my brand new princeton tec amp3.0 flashlight has a problem. with fresh batteries, I get a strong flash signal when pressing the on button, but the light does not stay on. as long as I keep pressing the button, the light will toggle, but not stay on. bulbs and abattery seem ok. can you help? thanks, Rob


From what you're telling me Rob I think that the button is defective from the factory.I would take it back for replacement or reund. To the best of my knowledge there is no easy way to repair it. Sorry I'm not more help. Thank you and hope you have good holidays
Read More At : Amp 3.0 LED Flashlight...

When i press the on off swith my flashlight wont stay on unless button is pressed.


The button is worn out and needs replaced; the catch mechanism inside the button is either broken off or worn out so much that it won't catch. In most cases, it is less expensive to replace the whole light. All things break eventually! Rate this solution!
Read More At : Streamlight...

Streamlight stinger LED 75711 will not turn all the way off. a very dim light stays on constantly


I think you are correct. Sounds like the switch.
Read More At : Stinger LED Rechargeable Flashlight-75711SL...

When I shake it it goes off


The switch is bad, contact Maglite at www.maglite.com and they will repair it under Warranty.
Read More At : 3 Cell D Blue Flashlight S3D116...

Rear Light will not stay on


Sounds like a bad contact in the switch. This seems to be a common problem.
Read More At : Flea Light Set...

The switch on our almost new Life Gear Glow 300 hour LED spot light is not working. We replaced the batteries as we assumed that was the problem. When the switch is depressed the light flashes briefly


Sounds like the switch is intermittently contacting an needs cleaned , tightened ,or replaced try some wd 40 in it .it wont hurt the electronics or take the switch apart an clean
Read More At : Life Gear Flashlights LED 300 Hr Glow Spot Red Model: LG114...

I have a Cyclops 2 cell (2xCR123) flashlight that looks like the current CYC-XCF, but has no clip on the side. I bought two CR123-size cells that are rechargeable, but did not notice they are 3.7v each when fully charged. I put the cells in the flashlight right out of the package and they were GREAT--the light was as bright as I have ever seen it. I then recharged the cells, and when the switch was pressed on, the bulb went POOF! Obviously, a bulb designed for 6v was not up to handling 7.4v! In fact, I found one web site which described the bulb as "Ultra Bright 80 Lumens Xenon Bulb (T1-1/2 Xenon 4.8V)," for the new light with the side clip. 4.8v bulb for 6v?? Can you give me a part number for, a bulb which can handle two 3.7v cells? Since the original bulb might be rated at 4.8v, theone I need might be rated at 6v (over-driven by the same percentage). Thank you, Joe Hathaway


The CR123 is a 6-volt cell.
Read More At : ® XRF Xenon Rechargeable Flashlight...

My new flashlight wont stay on


Flashlights of this type are notorious for poor design. I had one where the contact spring at the top broke its connection. Others break the ground wire when the top is unscrewed. Another design flaw is trying to solder a ground connection to the anodized aluminum case - doesn't work. I am replacing the broken ground wires with longer, more flexible ones but that's not a permanent solution. Some LED board case grounds have been repaired by scraping the solder-to-case joint although in one case I had to replace the joint by wedging in a piece of bare copper wire. Hope these tips help.
Read More At : Energizer...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.backpackingtips.net || Terms of Use || Contact || Privacy Policy
Load time: 0.0279 seconds