Guide :Camping, Backpacking & Hiking : Coleman Twomantle Dual Fuel Powerhouse Lantern ()

My lantern wont stay alight it slowly goes out why ??? aaagggghhhh

Single mantle version its difficult to light but i can get it going but it will only burn for a few mins then starts to fade away if i turn it upside down it brightens up for a few mins but then just fades out any ideas ?? please help me

Research, Knowledge and Information :

Coleman lantern will not light -

Coleman lantern will ... As far as my old lantern, 290-700, It doesn't want to stay lit and seems to loose ... It burns fine then goes almost completely out, ...
Read More At :

Gas burner takes ages to stay alight ??? [Archive] - Yachting ...

Taking the burner apart and cleaning the area around that flame sorted things out. Now both of my sensors ... the flame to stay alight. ... wont stay on, that usually ...
Read More At :

Gas Grill Repair - Grill wont light or stay lit - GardenFork ...

May 06, 2015 · Gas grill lights then goes out? Or gas grill wont light? ... Gas Grill Repair - Grill wont light or stay lit ... SLOWLY turn the gas valve on the tank on.

Gas furnace won't stay lit. cleaning the flame rod - YouTube

Mar 12, 2012 · Find out why Close. Gas furnace won't stay lit. cleaning the flame rod grayfurnaceman. Loading ... Gas Furnace will not stay lit on for more than few sec ...

Find Answers

If a liquid fuel lantern lights for only a few seconds then goes out, ... If the lantern lights for a few seconds then goes out and there is no sound of air passing ...
Read More At :

My Patio Heater Won't Light | Outdoor Order | 1-888-806-8836

If points 1 to 3 are OK the probable cause will be failure of the patio heater thermocouple. If the pilot on the patio heater lights up and then goes out when the gas ...
Read More At :

Light Bulb, Lighting Fixture and Lamp Troubleshooting

Troubleshooting Light Bulbs, Lighting ... or alkali can slowly leach into the hot quartz and ... High Pressure Sodium Lamp Repeatedly Goes Out for 1-3 Minutes After ...
Read More At :

Why do my LED lights stay on, even when the switch is off?

Swap out the light switches for regular ... depending on whether the neutral for the light goes through the same box as the ... why do my led lights stay on, ...
Read More At :

Suggested Questions And Answer :

My coleman dual fuel lantern wont let me pressure the fuel up with the plunger

Remove the plunger and oil the leather diaphram with light oil similar to 3 in 1 oil, and expand the diaphram until it is no longer stiff and contracted. If you do not know how to remove the plunger let me know.
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

My coleman powerhouse dual fuel lantern brightens and dims continuously. could this be the generator acting up?

Hi bradley m925... Try using the cleaner for the generator, it is a twist type crank, make a few turns on it if you have it. If not then your right, replace the generator as it is faulty. Please take time to rate me Coleman Generators website...
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

I have a dual fuel, two mantles, coleman lantern. I have changed the mantles several times and they keep getting holes almost every time i light the lantern.

Make sure that the vapourised fuel is coming through the mantle before lighting up. You should hear a hissing sound when the flame adjusting lever is turned to high. If not it is possible that the generator is clogged up and that vapourised fuel is not getting through to the mantle. So when you light up you are essentially just burning the mantle. If the generator is knackered it will need to be replaced. One way to check it to remove the generator, primed the tank and turn the valve on. If fuel spurts out when the generator is removed (DON'T LIGHT IT U)P THOUGH) but there is no hissing sound when the generator is intact then it is a sure sign that the generator is clogged up. In the UK a replacement generator should set you back £10-15. Hope this helps, Bandit
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

I have a Coleman single mantle dual fuel lantern. I have just fitted a new primer pump and i have vapour coming out and through the mantle but it will not ignite the mantle. Any suggestions please? Thanks

What kind of fuel are you using
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

Acts like a check valve is stuck open below the plunger assembly. It lets all the pressure out while im trying to pump it this something i can fix? the lantern is relatively new.

It sounds like you are correct. While I don't know much about the new lanterns I have worked a lot on older ones. My first suggestion is the easiest. Try putting some 3 in 1 oil on it. First relieve any pressure in the tank- open the valve then slowly loosen the fill cap- watch out as it will likely spill fuel so do this outside Remove the plunger, there is a black plastic piece that holds it in it will come of either by a push and twist, or by removing a little metal bail across it. (you remove the metal bail (small wire loop) by gently pulling it outward with a small pliers.) then the plunger should come right out look into the hole and you will see a check valve at the bottom, try a bit of oil or wd40 on this, let it sit for a while, it may just be rusted open, and will take some time for the oil to work. Make sure it is working well before you light the lantern. you Do Not want this to fail when the lantern is going. Do this outside and away from any flames. Pump it up and see if it can hold pressure overnight
Read More At : Coleman Twomantle Dual Fuel Powerhouse Lantern ()...

How to install new mantles? - Coleman Northstar Dual Fuel Lantern

First of all, make sure your lantern is completely shut off and cooled down, and you are working in a well ventilated area away from any external fuel sources. You need to remove the screw holding the top cap on, then remove the top and the glass globe. Then remove the remains of the old mantle(s) and then tie on the new ones in their place. Then, with the lantern fuel supply turned OFF, carefully light the mantles with a match or lighter and allow them to completely burn to ash and the flame to go out. Do not touch the mantles after this point because they will be very fragile. Now carefully replace the glass globe and screw the top back on. Now you can try lighting the lamp normally with the fuel valve in the ON position. Here are a few links to some short videos on YouTube which demonstrate the mantle replacement process: I hope that was helpful to you, good luck. If you choose to rate this solution using the Thumbs Up scale provided, I thank you very much for your time and consideration. Joe.
Read More At : Northstar Dual Fuel Lantern...

Hi there. I have been using my Coleman northstar for a week camping with Coleman fuel when it ran out I Began using unleaded petrol. It took a while but eventually worked fine. Now it doesn't work at all!! I have replaced the mantle but to no avail. It doesn't seem to have enough pressure to keep it lit no matter how much I pump it. Please help. Thanks... In the dark in Cornwall.

In the dark in Cornwall, have you visited Coleman's website?
Read More At : Northstar Dual Fuel Lantern...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0299 seconds